Mounts

Desk Mount for One Portable Scanner
This scanner stand for one scanner will look great on your desk or night table and conveniently hold just about any portable scanner radio. It's powder-coated black steel with rounded and smooth edges for a handsome look and feel. It includes two small round cutouts on either side of the scanner, and a hole in the back plate, to neatly snake through charger cords and PC programming cables. On the top a unique slot allows you to clip on scanners with belt clips or slide on scanners, such as the Bearcat BCD396T, which have a round metallic stud clip on the back. You can also simply stand any scanner on the bottom lip of the stand. Scanners can also be mounted in their carrying case on the stand multiple ways. You may purchase this mount from Scanner Master.


Desk Mount for Two Portable Scanners
Desk Mount fits two portable scanners. You may purchase this mount from Scanner Master.


Desk Mount for Three Portable Scanners
Desk Mount fits three portable scanners. You may purchase this mount from Scanner Master.


Desk Mount for Two Base Scanners
This 2-scanner Desk Mount, built with strong sheet-metal, allows you to attractively mount and display one or two base or base/mobile scanners that are approximately 7 to 7.5" wide. You can mount any combination of the following Uniden Bearcat Scanners: 760, 780, 785, 796, BCT15, BCD996T; GRE PSR400 and PSR600; and a variety of Radio Shack models including the 2053 and 2096 and similar models.

You can also drill holes in the bottom flanges to secure the mounting bracket to a desk or table but the radio weight keeps the unit from sliding in general. You can tilt the radios slightly upward for ease of operation if you desire. The front of the radios protrude approximately 1/2" from the edge of the metal providing a very strong and again, professional, appearance. Simply use the mobile mounting knobs (or bolts can easily be found at a local hardware store) to secure the scanners in place. These brackets are being used at news media assignment desks nationally as well as by hobbyists as a clean and attractive way to present and operate the radios. The brackets have been black-powder-coated to add to the professional look. The mount fits radios of 7.5" perfectly such as the DIN-E radios: The BCT15, BCD996T, PRO-2096, PSR400 and PSR600. But earlier scanners that are 7" wide will require the addition of a few washers or a nut. A three-high version is also available.

The dimensions are as follows: 7.5" wide (inside) by 6 1/8" deep by 6" high; the flange at the bottom is 1" wide. You may purchase this mount from Scanner Master.


Desk Mount for Three Base Scanners
This 3-scanner Desk Mount, built with strong sheet-metal, allows you to attractively mount and display between one and three base or base/mobile scanners that are approximately 7 to 7.5" wide. You can mount any combination of the following Uniden Bearcat Scanners: 760, 780, 785, 796, BCT15, BCD996T; GRE PSR400 and PSR600; and a variety of Radio Shack models including the 2053 and 2096 and similar models.

You can also drill holes in the bottom flanges to secure the mounting bracket to a desk or table but the radio weight keeps the unit from sliding in general. You can tilt the radios slightly upward for ease of operation if you desire. The front of the radios protrude approximately 1/2" from the edge of the metal providing a very strong and again, professional, appearance. Simply use the mobile mounting knobs (or bolts can easily be found at a local hardware store) to secure the scanners in place. These brackets are being used at news media assignment desks nationally as well as by hobbyists as a clean and attractive way to present and operate the radios. The brackets have been black-powder-coated to add to the professional look. The mount fits radios of 7.5" perfectly such as the DIN-E radios: The BCT15, BCD996T, PRO-2096, PSR400 and PSR600. But earlier scanners that are 7" wide will require the addition of a few washers or a nut. A two-high version is also available.

The dimensions are as follows: 7.5" wide (inside) by 6 1/8" deep by 9 1/8" high; the flange at the bottom is 1" wide. You may purchase this mount from Scanner Master.


Desk Mount for Four Base Scanners
4-scanner Desk Mount, built with strong sheet-metal, allows you to attractively mount and display between one and four base or base/mobile scanners that are approximately 7 to 7.5" wide. You can mount any combination of the following Uniden Bearcat Scanners: 760, 780, 785, 796, BCT15, BCD996T; GRE PSR400 and PSR600; and a variety of Radio Shack models including the 2053 and 2096 and similar models.

You can also drill holes in the bottom flanges to secure the mounting bracket to a desk or table but the radio weight keeps the unit from sliding in general. You can tilt the radios slightly upward for ease of operation if you desire. The front of the radios protrude approximately 1/2" from the edge of the metal providing a very strong and again, professional, appearance. Simply use the mobile mounting knobs (or bolts can easily be found at a local hardware store) to secure the scanners in place. These brackets are being used at news media assignment desks nationally as well as by hobbyists as a clean and attractive way to present and operate the radios. The brackets have been black-powder-coated to add to the professional look. The mount fits radios of 7.5" perfectly such as the DIN-E radios: The BCT15, BCD996T, PRO-2096, PSR400 and PSR600. But earlier scanners that are 7" wide will require the addition of a few washers or a nut. A two-high and a three-high version are also available.

The dimensions are as follows: 7.5" wide (inside) by 6 1/8" deep by 12" high; the flange at the bottom is 1" wide. You may purchase this mount from Scanner Master.




PRODUCTS

•Lapel Speaker

•Antenna with BNC

•Antenna with SMA

•Desk Mount 1 Portable

•Desk Mount 2 Portable

•Desk Mount 3 Portable

•Desk Mount 2 Base

•Desk Mount 3 Base

•Desk Mount 4 Base

 

Scanner Master Corp | scannermaster.com